Fix running toilet problems by checking the flapper first, because a worn flapper is the most common cause. If the flapper seals well, check the fill valve next. If water is on the floor or the toilet still runs after both checks, book toilet service.
Why A Toilet Keeps Running
The flapper is the rubber seal at the bottom of the tank. When it wears out, water slips from the tank into the bowl. The water level in the tank drops, the float drops with it, and the fill valve turns the water back on.
The other cause is the fill valve. If the float is set too high, or the valve is clogged or worn, water keeps flowing after the tank is full and spills down the overflow tube. A loud bang as the tank refills is a different fault, so read about a banging refill.
Check The Flapper
Here is how to repair a toilet that keeps running, one step at a time:
- Put a few drops of food colouring in the tank, and do not flush.
- Wait 10 minutes, and look in the bowl. Colour in the bowl means the flapper is leaking.
- Flush right after the test so the dye does not stain the tank.
There is a second test you can try. Flush, let the tank fill, and mark the water line with a pencil. Turn off the water to the toilet, and wait at least 25 minutes. If the water drops to the flapper, the flapper or its seal needs to be changed. If it drops lower, to the overflow tube or the bottom of the tank, the flush valve needs to be changed.
Next, check the chain. It needs 1 or 2 links of slack. A chain that is too tight holds the flapper open, so the toilet runs.
Also look at the ring the flapper sits on. Clean off any mineral build up so the flapper can seal.
A flapper should be checked from time to time and changed at least every 5 years. Take the old one, or a photo of it, to the hardware store so the new one fits.
Check The Fill Valve
Flush, and watch the tank while it fills. If water keeps running after the tank is full, the float may be stuck or set too high.
You can adjust the float, clean the valve, or put in a new valve. Turn off the water to the toilet before you start. Most fill valves last 5 to 7 years. Read about a worn fill valve for the swap steps, and begin by emptying the tank.
Leaks And Weak Flushes
Is water dripping from the bolts under the tank? The rubber gasket between the tank and the bowl wears down over time, and the fix is a new gasket and bolts. That is how to repair a leaking toilet at the tank, but it means taking the tank off. Seals come in a 2 inch and a 3 inch size, so read about a slow tank drip to pick the right one.
A weak flush often comes from the same parts, such as a chain that is too loose to lift the flapper, or a float set so low that the tank does not fill. The small holes at the top of the bowl can also clog with minerals over time. If the handle sticks or does not spring back, read about a sticking handle.
If water is getting on the floor, read about stopping leaks. If the toilet rocks or you see water at the base, check the flange under it.
When To Call A Plumber
Call a plumber if the toilet still runs after you check the flapper and the fill valve. Call too if water leaks at the base of the bowl, or if you would rather not take the tank off. If you are not sure how to repair toilet flush parts, a plumber can do it for you.
If the toilet drains slowly or backs up, read about drains. For leaks at the base and clogs, see our guide to toilet faults.
Why Does My Toilet Run Continuously?
A toilet running continuously most often has a worn flapper that lets water leak into the bowl. The 10 minute colour test will tell you. If the flapper is fine, the fill valve may not be shutting off.
Is A Running Toilet Wasting Water?
Yes, it is. The U.S. EPA says a worn flapper can leak thousands of gallons of water a year without a sound. It can also make the toilet flush on its own.
Can I Repair A Flush Valve Myself?
The flapper is a quick part to change. The whole flush valve is a bigger job, because the tank has to come off the bowl.